Gel coat is the outer layer of fiberglass. Its structural value is not significant. However, it gives the product its shine and color. In addition, it offers protection to the hull. Read on to know more on how to restore faded fiberglass.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If mildew is present, bleach will have to be utilized in the cleaning process. Additionally, concentrated cleaning formulation should be used when stubborn stains are present. The surface should be rinsed with clean water so that all the detergent present is washed away. Thereafter, allow the item to dry off. If you are in a hurry, you can dry it manually.
For better results, all oil should be removed from the item. Not all detergents succeed in accomplishing this. Acetone or MEK should be used for this purpose. However, it is advisable to use a microfiber cloth to apply it. Direct application is discouraged. You may need several of them because you have to discard it once they are covered up with grease. The next step is to wax the item. This can prolong its life.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
The next step is polishing. This should be done using an abrasive. Fine sandpaper is preferred. It will remove pitted areas. This is not something you can achieve with coating. You should tackle a small section at a time. In addition, the motions have to be circular. Go on until you can see your reflection on the surface. An extra layer of wax should be added after you are done polishing for protection. Some preparations contain wax in the formulation.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer is applied last. They are quite a number and you cannot fail to get a suitable one in the market. However, it acts just like wax. Nonetheless, there is no need to buff your fiberglass after you are done applying it. The end product is impressive. However, this effect will only last for a considerable duration if you take care of the product. Nonetheless, you will have to restore it after sometime.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If mildew is present, bleach will have to be utilized in the cleaning process. Additionally, concentrated cleaning formulation should be used when stubborn stains are present. The surface should be rinsed with clean water so that all the detergent present is washed away. Thereafter, allow the item to dry off. If you are in a hurry, you can dry it manually.
For better results, all oil should be removed from the item. Not all detergents succeed in accomplishing this. Acetone or MEK should be used for this purpose. However, it is advisable to use a microfiber cloth to apply it. Direct application is discouraged. You may need several of them because you have to discard it once they are covered up with grease. The next step is to wax the item. This can prolong its life.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
The next step is polishing. This should be done using an abrasive. Fine sandpaper is preferred. It will remove pitted areas. This is not something you can achieve with coating. You should tackle a small section at a time. In addition, the motions have to be circular. Go on until you can see your reflection on the surface. An extra layer of wax should be added after you are done polishing for protection. Some preparations contain wax in the formulation.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer is applied last. They are quite a number and you cannot fail to get a suitable one in the market. However, it acts just like wax. Nonetheless, there is no need to buff your fiberglass after you are done applying it. The end product is impressive. However, this effect will only last for a considerable duration if you take care of the product. Nonetheless, you will have to restore it after sometime.
About the Author:
You can visit www.leprechaunmagic.com for more helpful information about Concerning How To Restore Faded Fiberglass.
No comments:
Post a Comment